Try Latest 300-615 DCIT Practice Exam For CCNP Data Center Certification

test2022-06-24T03:40:45+00:00

You must pass the 300-615 DCIT exam if you want to obtain CCNP Data Center certification. FreeTestShare is the place to go if you want to acquire all of the latest 300-615 DCIT Practice Exam. FreeTestShare 300-615 DCIT Practice Exam contains actual exam questions and answers, ensuring that you pass the exam on your first attempt. Real 300-615 questions and answers are included in the Troubleshooting Cisco Data Center Infrastructure (DCIT) Exam, which have been revised and updated to guarantee that they are accurate and up to date. If you want to pass 300-615 exam fast, get 300-615 DCIT Practice Exam to smoothen your prep well!

Try these 300-615 practice test questions to see if you are ready for the real exam.

Page 1 of 4

1. Refer to the exhibit.

The vPC between switch1 and switch2 does not work .

Which two actions resolve the problem? (Choose two.)

Configure the IP address on the interface.

Activate VLANs on the vP

Configure one of the switches as primary for the vP

Correct the configuration of the vPC peer link and the vPC peer keepalive.

Match the vPC domain ID between the two devices.

2. Refer to the exhibit.

A switch is being downgraded to an earlier release because of a problem with the current release. After the switch is downgraded, it can no longer forward traffic .

Which action resolves the issue?

Enable ISSD after the downgrade is complete.

Roll back to the original image.

Reload the switch.

Shut and no shut the interfaces to the FE

3. Refer to the exhibit.

The EEM script overrides all events in the system policy .

What should be added to the script to resolve the issue?

event statement

environment variable

event-default action statement

configure terminal action

4. Refer to the exhibit.

An engineer must strictly enforce the port security configuration database in the Fibre Channel fabric. A new device has been connected to the Fibre Channel storage interface that was configured for port security. The port security was enabled for the VSAN that the port belongs to. Despite the configuration, the rogue devices can log into the fabric .

Which action resolves the issue?

Commit the active database with the port-security database copy vsan 1 command

Disable auto learn in VSAN 1 with the no port-security auto-learn vsan 1 command

Disable CFS distribution with the no port-security distribute vsan 1 command

Commit the changes with the port-security commit copy vsan 1 command

5. A server fails to boot from the operating system after a RAID1 cluster migration. The RAID remains in an inactive state during and after a service profile association .

Which action resolves the issue?

Configure the SAN boot target in the service profile.

Configure the SAN boot target to any configuration mode.

Use a predefined local disk configuration policy.

Remove the local disk configuration policy.

6. An engineer is implementing a new BGP peering in their new data center. The engineer set up the BGP session that peers with the remote end. As soon as the BGP peers attempt to exchange routing prefixes, one of the BGP peers drops the connection. After reviewing the configuration, the engineer reviews the logging messages. The engineer discovers that the router is missing keepalives from the remote end and terminates the session .

Which action resolves the issue?

Set the bgp transport path-mtu-discovery attribute on both peers

Set the higher values for the BGP keepalive and hold-down timers on both peers

Configure the matching BGP AS numbers between the peers

Configure the matching BGP passwords between the peers

7. DRAG DROP

Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.

8. An engineer attempts to register Cisco UCS Manager to Cisco UCS Central, but the registration fails. The engineer can ping Cisco UCS Central from UCS Manager .

Which two actions must the engineer attempt to resolve the problem? (Choose two.)

Synchronize the date and time to NTP for Cisco UCS Central and the Cisco UCS domains.

Apply the UCS Central license to UCS Central.

Place Cisco UCS Manager on the same subnet as Cisco UCS Central.

Allow port 443 between Cisco UCS Manager and Cisco UCS Central.

Allow port 9443 between Cisco UCS Manager and Cisco UCS Central.

9. Refer to the exhibit.

A web browser displays a “not secure” warning message when accessing the web interface of Cisco UCS Manager .

Which action resolves the issue?

Load third-party certificate to UCS Manager.

Use the correct TCP port for HTTP

Use a supported web browser.

Use a supported version of UCS Manager.

10. During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a "No Signal" message from the vKVM and physical connection .

Which set of steps resolves the issue?

1- Disconnect the power cord 2- Confirm that all cards are property seated 3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord 2- Confirm that all cards are property seated 3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord 2- Confirm that all cards are available 3- Connect the power cord and power on the server

1- Disconnect the power cord 2- Confirm that all cards are properly seated 3- Connect the power cord

Page 2 of 4

11. A request to activate the port security database is rejected .

Which action do you perform to investigate the cause of the issue?

Enable the auto-learning feature.

Use the force option to identify rejected devices.

Find conflicting entries between the active and configuration databases.

Verify that devices are fully attached to the active database.

12. Refer to the exhibit.

An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails to mount .

Which action resolves the issue?

Statically configure the target information in the Boot Policy.

Configure an MTU size of 9000 on the appliance port.

Configure a QoS policy on the vNI

Set a connection timeout value of 250 in the iSCSI Adapter Policy.

13. Refer to the exhibit.

After the configuration is performed, guestshell continues to use 2%CPU .

Which action resolves the issue?

Resync the database

Recreate the guestshell

Reboot the guestshell

Reboot the switch

14. A system administrator adds two vNICs to an existing service profile that is used to run a vSphere environment to support disjoint Layer 2 network connectivity. However, after the server is rebooted, the host is not accessible on the network.

Which action resolves the issue?

Remove all existing vNICs and add them in the desired order.

Build a new service profile with the desired network configuration

Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs

Create a vNIC placement policy to avoid adapter renumbering

15. Refer to the exhibit.

A Cisco UCS Fabric Interconnect fails during the upgrade process. The working images of the fabric interconnect are stored on the bootflash .

Which set of commands recovers the fabric interconnect?

loader> dir loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin switch(boot)# init system switch(boot)# reload switch(boot)# load ucs-6300-k9-system.5.0.2.N1.3.02d56.bin

loader> dir loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin switch(boot)# copy ics-manager-k9.1.4.1k.bin nuova-sim-mgmt-nsg.0.1.001.bin switch(boot)# boot ucs-6300-k9-system.5.0.2.N1.3.02d56.bin

loader> dir loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin switch(boot)# init system switch(boot)# reload switch(boot)# boot ucs-6300-k9-system.5.0.2.N1.3.02d56.bin

loader> dir loader> boot ucs-6300-k9-kickstart.5.0.2.N1.3.02d56.bin switch(boot)# copy ics-manager-k9.1.4.1k.bin nuova-sim-mgmt-nsg.0.1.001.bin switch(boot)# load ucs-6300-k9-system.5.0.2.N1.3.02d56.bin

16. You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership .

What is the cause of the issue?

The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.

Rebooting the APICs and the leaf and spine switches after wiping them is not required.

You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.

The same Fabric Name value should be used before after wiping all devices.

17. Refer to the exhibit.

An engineer configures the server port on a Cisco Nexus 5000 Series Switch. The switch connects to an NPV edge switch port. The server fails to send the FC traffic to the fabric .

Which action resolves the issue?

Enable the NPIV mode on the Cisco Nexus 5000 switch.

Match the VSAN membership on both ends of the connection.

Configure the BB_credit buffer on the uplink port.

Replace the SFP in slot fc2/12.

18. Refer to the exhibit.

A PC belongs to VLAN 68 The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68 .

Which action resolves the problem?

Replace HSRP with GLBP

Enable the peer-gateway feature

Remove the HSRP configuration

Configure ip arp synchronization on both switches.

19. An IOM fails during a firmware upgrade and is unresponsive .

Which action recovers the module?

Restore UCSM configuration from backup.

Roll back to the previous firmware.

Use AutoInstall to reinstall the firmware.

From the peer IOM, reset the faulty module.

20. Refer to the exhibit.

The vPC neighborship between two switches is in suspended state .

Which configuration change resolves the issue and brings up the vPC neighborship?

Change STP Port Type to Network on the peer switch

Enable Bridge Assurance on the local switches

Configure QoS MTU value of 9216 on the peer switch

Add VLAN 400-401 to the configuration on the local switch

Page 3 of 4

21. Refer to the exhibit.

Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain .

Which statement describes what happens in this scenario?

Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.

Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.

Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.

Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VN

22. An upgrade of protected RPMs from the Bash shell did not take effect .

Which action is required for the changes to take effect?

Restart the Bash shell.

Reload the switch.

Upgrade the RPMs from the Guest shell.

Disable and reenable the Bash feature.

23. Refer to the exhibit.

An engineer must connect N2K-Fex-1 and N5K-Core-1 so that the traffic flow between the two devices uses load balancing. After inspecting the statistics of the interconnecting interfaces, the engineer concludes that only one link is used .

Which action resolves the problem?

Configure source-destination load balancing on N5K-Core-1.

Configure each uplink to be a member of a separate LACP port channel.

Configure the pinning max-link as 2.

Configure destination-mac load balancing on N5K-Core-1

24. An engineer is troubleshooting a failed DCBX exchange between a server and a Cisco Nexus switch .

Which action allows DCBX to successfully negotiate?

Enable ETS

Enable PF

Enable Cisco Discovery Protocol.

Enable LLD

25. 1.Refer to the exhibit.

A network engineer upgrades the firmware of a Cisco Fabric Interconnect from boot flash. During the process, the fabric interconnect reboots and displays the message shown in the exhibit .

Which action resolves the issue?

Remove the service pack and upgrade through the auto-install procedure

Reset the I/O module and install the firmware image from the boot flash

Boot the kickstart image from boot flash and load the system image

Reload the switch and boot the kickstart image from the TFTP server

26. Refer to the exhibit.

A client configures an upgrade of its Cisco Nexus switches that are connected to the Cisco ACI controller, such that the switches are upgraded one at a time. After the upgrade is run, it is discovered that both Cisco Nexus switches were upgraded simultaneously .

Which two actions ensure that the switches upgrade one at a time? (Choose two.)

Configure the *Do not pause on failure and do not wait on cluster health" Run Mode

Choose the 'Pause upon upgrade failure" Run Mode

Select the "Graceful Maintenance" checkbox

Place each leaf switch in a different upgrade group

Check the Ignore Compatibility" checkbox

27. Refer to the exhibit.

When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails .

What is a possible cause of the issue?

Port 15 is configured as an Ethernet port.

Port 15 is configured for 4-Gb F

Port 15 is missing a license.

The polarity of the fiber cable is reversed.

28. Refer to an exhibit.

An engineer is troubleshooting an upgrade failure on a switch .

Which action resolves the issue?

Save the system image in NVRA

Use the same system image as the kickstart image.

Load a new system image.

Reload the same system image.

29. An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After

the replacement was done, the server has a “resolve slot” warning .

Which server maintenance action resolves the issue?

Perform diagnostic interrupt on the server.

Re-acknowlegement the server.

Reset the server.

Decomission the server.

30. After upgrading a client’s fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration .

Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)

Equipment FSM page, InternalBackup stage

Service profiles page, InternalBackup stage

Admin page, PollInternalBackup stage

Equipment FSM page, PollInternalBackup stage

Admin page, InternalBackup stage.

Page 4 of 4

31. One of Cisco Nexus Series interfaces has become errdisabled with the error message “DCX-No ACK in 100 PDUs” .

What is the cause of this error?

The host has not responded to the Control Sub-TLV DCBX exchanges of the switch.

The acknowledgement number in the server response has not incremented for 100 exchanges.

Cisco Discovery Protocol is disabled on the switch.

LLDP is disabled on the switch.