2022 Free & Valid JNCIS-SP JN0-363 Questions and Answers Online

test2022-12-05T07:20:58+00:00

By test JN0-363 free dumps, JN0-363 practice exam, JNCIS-SP JN0-363 Questions and Answers 0 Comments

Valid JNCIS-SP JN0-363 Questions and Answers are offered for free, which can help you best prepare for your test. Service Provider Routing and Switching, Specialist (JNCIS-SP) exam verifies your basic understanding of routing and switching technologies and related platform configuration and troubleshooting skills. You can study the latest JNCIS-SP JN0-363 Questions and Answers with real exam objectives so that you can pass your Juniper JN0-363 exam sucessfully.

Here we’ve prepared some real JN0-363 exam questions. Have a try!

Page 1 of 2

1. Which statement is correct about the FE80;:/10 prefix?

This prefix range is used for the link local address.

This prefix range is used on the loopback interface.

This prefix range is reserved for multicast applications

This prefix range is not reserved.

2. Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSAASBR into the backbone?

Type 5

Type 7

Type 3

Type 1

3. Exhibit

Referring to the exhibit, what must be included in the Route1 configuration when establishing an EBGP session with the ISP?

A local address must be specified.

A local AS must be specified.

The BGP session type internal must be specified.

The BGP session type external must be specified.

4. Exhibit

The LSP is not establishing correctly.

Referring to the exhibit, what should you do to solve the problem?

Enable traffic engineering for the OSPF protocol.

Enable traffic engineering for the IS-IS protocol.

Enable traffic engineering for the BGP protocol.

Enable traffic engineering for the RSVP protocol.

5. Which new field is added to an IPv6 header as compared lo IPv4?

version

checksum

fragment offset

flow label

6. Exhibit.

Referring to the exhibit, you have configured an aggregate route that represents the 172.2 1. 0.0/24, 172.2 1.1. 0/24, and 172.2 1. 2.0/24 networks. However, when you view the routing table, your new route hidden.

Which action would you perform to determine the problem?

Verify that you have active contributing routes on the device.

Verify that you have configured a policy on the device to accept aggregate routes.

Verify that you have defined a metric value for the aggregate route.

Verify that you have set the preference to a lower default value.

7. What is the correct order of BGP attributes for active route selection?

next hop -> local preference -> AS path -> MED -> origin

next hop -> AS path -> local preference -> origin -> MED

next hop -> local preference -> AS path -> origin -> MED

next hop -> origin -> local preference -> AS path -> MED

8. Exhibit

You have configured graceful RE switchover (GRES), however you cannot complete the show system switchover command.

Referring to the exhibit, what is the problem?

The command is only available if non-stop routing is enabled.

The command is only available on the backup Routing Engine.

The command is only available If a backup router is configured.

The command is only available If graceful restart is enabled.

9. Exhibit

Referring to the exhibit, which statement is true about VRRP?

VRRP communication between the two devices is not functioning correctly.

Both routers are in the same state because they have the same VRRP priority.

RRP Is functioning normally in active/active mode.

The routers should use different virtual IP addresses for VRRP to function correctly.

10. Exhibit

You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.

What is the problem in this scenario?

This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

The family iso statement must be added to the logical interface.

The router at the other end of the link Is not sending any IS-IS Hello messages.

The router at the other end of the link is a Level 1 only router.

Page 2 of 2

11. Which two statements ate correct about the community BGP attribute on a Junos device? (Choose two.)

The community attribute is a mandatory BGP attribute.

If the community attribute is present, it is ignored and deleted in the BGP updates.

If the community attribute is present, it should be passed unchanged in the BGP updates.

The community attribute is an optional BGP attribute.

12. Exhibit

Referring to the exhibit, which two statements are correct? (Choose two.)

The OSPF Interfaces are configured as point-to-point.

The ge-0/0' 1. 0 Interface is configured as passive.

The R2 device is an AB

Junos OS default OSPF hello timers and dead intervals are used on all interfaces.

13. Which two LSA types are permuted in OSPF totally stubby areas? (Choose two.)

Type 1

Type 3

Type 5

Type 7